Lns license access failure

Some municipalities want to install automatic license plate readers along Lake County roadways, but County Board members are concerned about the data that could be gathered by such devices. However, several members of the committee, as well as other board members, chimed in at the meeting to say they are concerned about privacy and data issues that could arise from it.

Despite those worries, board members agreed it would be beneficial to police and public safety. The committee decided to move forward with the idea, but also said that more information was needed.

On that note, many questions from the discussion went partially to completely unanswered, as county staff reminded members throughout that this was early in the process. The item is likely to be revisited in early , officials said. Automatic license plate readers are cameras that are installed along roadways that capture vehicle information with time stamps.

The readers are typically used by police departments to help with investigations. Showing results for. Search instead for. Did you mean:. All Community This category This board. Config below portions stripped for security version Labels: Labels: Other Service Provider. Tags: asrx. I have this problem too.

All forum topics Previous Topic Next Topic. Post Reply. Latest Contents. Listen: smarturl. The IT Blog Awards is now accepting submissions! Configure the "Local" subscriber with L2TP tunnel parameters and the load balancing parameters with action by applying the example configuration in the Configuring Local Subscriber section.

Use the following example to configure the Local subscriber with L2TP tunnel parameters. Optionally you can configure load balancing between multiple LNS servers:. These instructions are used to verify the L2TP configuration. Verify that your L2TP configurations were configured properly by entering the following command in Exec Mode in specific context:. As with other services supported by the system, values for subscriber profile attributes not returned as part of a RADIUS Access-Accept message can be obtained using the locally configured profile for the subscriber named default.

The subscriber profile for default must be configured in the AAA context i. To configure the profile for the subscriber named default, follow the instructions above for configuring a local subscriber and enter the name default.

Prior to Not all commands, keywords and functions may be available. Functionality is dependent on platform and license s. This section provides information and instructions for configuring LAC services on the system allowing it to communicate with peer LNS nodes.

This section provides the minimum instruction set for configuring LAC service support on the system. By default, this feature is disabled. These instructions are used to verify the LAC service configuration. Verify that your LAC service configurations were configured properly by entering the following command in Exec Mode in specific context:. PDSN service modification is required for compulsory tunneling and optional for attribute-based tunneling.

For attribute-based tunneling, a configuration error could occur such that upon successful authentication, the system determines that the subscriber session requires L2TP but cannot determine the name of the context in which the appropriate LAC service is configured from the attributes supplied. As a precautionary, a parameter has been added to the PDSN service configuration options that will dictate the name of the context to use.

It is strongly recommended that this parameter be configured. This section contains instructions for modifying the PDSN service configuration for either compulsory or attribute-based tunneling. These instructions are used to verify the PDSN service configuration.

The output of this command is a concise listing of PDSN service parameter settings as configured. These instructions are used to verify the APN configuration.

Verify that your APN configurations were configured properly by entering the following command in Exec Mode in specific context:. Skip to content Skip to search Skip to footer. Book Contents Book Contents. Find Matches in This Book. PDF - Complete Book Updated: October 7, Figure 1. Figure 2. The PDSN service attempts to authenticate the subscriber.

The encapsulated packets are sent to the peer LNS through the packet data network where they will be un-encapsulated. Important These instructions assume that the system was previously configured to support subscriber data sessions as a PDSN. Procedure Step 1 Configure the subscriber profiles according to the information and instructions located in the Configuring Subscriber Profiles for L2TP Support section of this chapter.

PDSN Service-based Compulsory Tunneling This section describes the working of service-based compulsory tunneling and its configuration. The following figure and the text that follows describe how PDSN service-based compulsory tunneling is performed using the system. Figure 3. Each LAC service is bound to a single system interface configured within the same system destination context as displayed in following figure.

Figure 4. Figure 5.